Australian Pulse Bulletin

Chickpea fungicide guide: 2019 season

Foliar fungicides can help manage the chickpea diseases Ascochyta blight (AB) and Botrytis grey mould(BGM), but when to commence a fungicide program and how often to spray, depends on the varietal resistance, weather conditions and the potential yield of the crop. Bear in mind that AB is endemic in paddocks that have a history of chickpea in many areas of Qld and NNSW and BGM is a widespread disease of many crops so crop rotations and cultural practices should be considered when growing chickpeas. Chickpea after chickpea can never be recommended as varietal resistance will be reduced or overcome.

Pulse Australia have Minor Use Permits from APVMA in place for 2019 to help growers with disease control and these are shown in the table below along with all the current registered products.

Fungal disease control is based on the use of integrated disease management to minimise the injury to crops from plant pathogens. Efficient use of foliar fungicides is based upon the protection of plants rather than curing existing infections. The first fungicide application must be applied as early as necessary to minimise the establishment of the disease especially in paddocks that have had a history of pulse crops. Current research shows that a fungicide application prior to rain events at the early vegetative stage will give protection from AB that can translate to yield increases or at least to maintaining expected yields. Additional fungicide applications are required if weather conditions favour the disease, but the best management recommendation for disease control remains that foliar fungicides should be applied prior to forecast rain to provide the greatest level of protection. Post-infection applications should not be a planned part of your standard disease management plan. Chlorothanonil and mancozeb are persistent and rain-fast, but do not prevent infection if applied after rain starts.

Fungicides remain effective on leaves that are given good coverage, but keep in mind that all new growth after spraying is unprotected. In winter new leaves may take 5-7 days to grow but in spring as conditions warm up this is reduced to 2-3 days. Timing of fungicide applications is critical. An application in advance of a rain front provides maximum protection. Delaying application until after a rain front reduces efficacy significantly, as rainfall will rapidly promote spread of inoculum. With high levels of inoculum in many paddocks,[KJM2] a protective fungicide application soon after crop emergence may be required. Close monitoring for early symptoms will give greater opportunities to minimise disease establishment and yield loss.

The need for repeated fungicide applications depends on the growth stage of the crop, the time since the last fungicide application and the likelihood of further conditions favouring disease development. Unprotected crops may be quickly defoliated and destroyed by the infection. Under disease conducive conditions, varieties that are susceptible to AB will require multiple sprays through the season, while varieties with moderate susceptibility to AB will require at least 3-4 sprays over the season.

Seasonal Conditions in 2019

Seasonal conditions have varied widely across Australian cropping areas. After a very hot and dry summer in many regions and variable autumn break for sowing crops, conditions in many regions have become cold and dry, with frosty mornings. In Central Qld conditions have been favourable for crop establishment, but Southern Qld and Northern NSW drought conditions have prevailed since 2017 in many areas, with prospects for winter crops again below average. South Eastern NSW has had some reasonable rainfall, slightly below average, and crops are progressing slowly. In South West NSW though many crops are suffering moisture stress and are well below average. Victoria and South Australia also have average conditions to start but have had reasonable mid-season rainfall to get crops established well. Further rain will be needed in spring to finish these crops. In Western Australia the southern and eastern grain belts have again had a dry start, similar to 2018, but recent rainfall has improved prospects. These conditions have meant that diseases need to be monitored closely in many regions. Monitoring needs to be continued through the different growth stages of the crop. With good access for ground sprayers this year, allowing for high water rates and canopy penetration, timely fungicide application will give the crop the best chance of a high yield. 

For more detailed information on disease management: 

• Chickpea: Integrated disease management
• CropPro chickpea crop disease manual
• Fungicide resistance in grain crops (including pulses)

• 

  Ascochyta blight on chickpea pod (G Cumming)

• 

  'Ghosting' caused by ascochyta blight on chickpea leaves (SARDI)

• 

  Botrytis grey mould (P Davis)

Fungicide Minor Use Permits for chickpea 2019

• PER81406 Captan / Ascochyta blight, chocolate spot, grey mould / Current to 30-Sep-2023 (All States)
• PER81533 Custodia / Ascochyta blight, grey mould / Current to 30-Sep-2019 (All States)
• PER85440 Penflufen /Fusarium Wilt / Current to 31-July-2021 (seed treatment)

Fungicides registered for use on chickpea

Chickpea Foliar Fungicide	Trade Name example	Ascochyta	Botrytis	WHP Harvest
Chlorothalonil 720	CC Barrack 720	1.0–2.0 L/ha	NR	14 days
Mancozeb 750	Dithane SC	1.0–2.2 L/ha	1.0–2.2 L/ha	28 days
Mancozeb 420	Penncozeb SC	1.8–3.95 L/ha	NR	28 days
Carbendazim	Spin Flo	NR	500 mL/ha	28 days
Captan 900	CC Captan 900	Permit 1.1 kg/ha	Permit 1.1 kg/ha	14 days
Captan 800	CC Captan 800	Permit 1.25 kg/ha	Permit 1.25 kg/ha	14 days
Azoxystrobin 120 g/L and Tebuconazole 200 g/L	Custodia (Veritas)	Permit 1.0 L/ha	Permit 1.0 L/ha	28 days
Metiram 700	Polyram DF	1.0–2.2 kg/ha	1.0–2.2 kg/ha	42 days
Bixafen + Prothioconazole	Aviator	400–600 mL/ha	NR	35 days

Many of the Minor Use Permits have short term expiry dates (e.g. 30/11/2017) 

NR = Not Registered 

Read the Label As with any chemical application, care should be taken to observe all the label conditions for each product. Some label advice is different for each state or region, so for best results, it is important that this is followed. Many of our pulse crops are exported for human consumption, so market access is dependent on having the product free of chemical residues. Australian has a reputation for providing clean and safe produce so it is vital that this is maintained by using chemicals according to regulations. All permits have label recommendations for use rate and withholding periods (WHP) that must be observed so grain will comply with Maximum Residue Limits (MRL) allowable for market access.

Key contacts

Last updated: 4 September 2019